Chevy V8 bore & stroke chart

by RebStew February 9th 2008, 3:28 am

CHEVY SMALLBLOCK V-8 BORE AND STROKE

262 = 3.671" x 3.10" (Gen. I, 5.7" rod)
265 = 3.750" x 3.00" ('55-'57 Gen.I, 5.7" rod)
265 = 3.750" x 3.00" ('94-'96 Gen.II, 4.3 liter V-8 "L99", 5.94" rod)
267 = 3.500" x 3.48" (Gen.I, 5.7" rod)
283 = 3.875" x 3.00" (Gen.I, 5.7" rod)
293 = 3.779" x 3.27" ('99-later, Gen.III, "LR4" 4.8 Liter Vortec, 6.278" rod)
302 = 4.000" x 3.00" (Gen.I, 5.7" rod)
305 = 3.736" x 3.48" (Gen.I, 5.7" rod)
307 = 3.875" x 3.25" (Gen.I, 5.7" rod)
325 = 3.779" x 3.622" ('99-later, Gen.III, "LM7", "LS4 front wheel drive V-8" 5.3 Liter Vortec, 6.098" rod)
327 = 4.000" x 3.25" (Gen.I, 5.7" rod)
345 = 3.893" x 3.622" ('97-later, Gen.III, "LS1", 6.098" rod)
350 = 4.000" x 3.48" (Gen.I, 5.7" rod)
350 = 4.000" x 3.48" ('96-'01, Gen. I, Vortec, 5.7" rod)
350 = 3.900" x 3.66" ('89-'95, "LT5", in "ZR1" Corvette 32-valve DOHC, 5.74" rod)
364 = 4.000" x 3.622" ('99-later, Gen.III, "LS2", "LQ4" 6.0 Liter Vortec, 6.098" rod)
376 = 4.065" x 3.622" (2007-later, Gen. IV, "L92", Cadillac Escalade, GMC Yukon)
383 = 4.000" x 3.80" ('00, "HT 383", Gen.I truck crate motor, 5.7" rod)
400 = 4.125" x 3.75" (Gen.I, 5.565" rod)
427 = 4.125" x 4.00" (2006 Gen.IV, LS7 SBC, titanium rods)

Two common, non-factory smallblock combinations:

377 = 4.155" x 3.48" (5.7" or 6.00" rod)
400 block and a 350 crank with "spacer" main bearings
383 = 4.030" x 3.75" (5.565" or 5.7" or 6.0" rod)
350 block and a 400 crank, main bearing crank journals
cut to 350 size

--------------------------------------------------------------------------------

CHEVY BIG BLOCK V-8 BORE AND STROKE

366T = 3.935" x 3.76"
396 = 4.096" x 3.76"
402 = 4.125" x 3.76"
427 = 4.250" x 3.76"
427T = 4.250" x 3.76"
454 = 4.250" x 4.00"
496 = 4.250" x 4.37" (2001 Vortec 8100, 8.1 liter)
502 = 4.466" x 4.00"
572T = 4.560" x 4.375" (2003 "ZZ572" crate motors)

T = Tall Deck

ALL production big blocks used a 6.135" length rod.

--------------------------------------------------------------------------------

CHEVY 348-409 V-8 BORE AND STROKE

348 = 4.125" x 3.25" (6.125" rod)
409 = 4.312" x 3.50" (6.010" rod)
427 = 4.312" x 3.65" (6.135" rod) 1963 "Z11" SHP drag race

by motorjunkie September 12th 2012, 5:39 am

Hey can you tell me how big of a bore and stroke I can use on the GM 350 (4.000 x 3.48). I'm looking to upgrade the motor from what it's at now and try to get as much horsepower and torque as I can out of it.

by Reb Stew September 12th 2012, 5:48 am

There are all kinds of ways to get more cubes out of a 350. Thing is, IS IT WORTH IT? You can buy stroker kits such as the one in this link > http://www.superchevy.com/technical/engines_drivetrain/completebuilds_testing/sucp_0706_small_block_chevy_stroker_kit/viewall.html

Or just buy you a big block 454 and go that route. If your pocket are deep you can buy a 572 Crate engine.

by Sinner December 2nd 2012, 11:20 pm

Yeah, the easiest is the stroker kit. I like to mix it up a bit, though. All depends on the bucks you want to drop on it. Just remember if you're going to spray it then you should go with forged pistons and some GOOD rings.

by Sponsored content

Chevy V8 bore & stroke chart

Chevy V8 bore & stroke chart

Re: Chevy V8 bore & stroke chart

Re: Chevy V8 bore & stroke chart

Re: Chevy V8 bore & stroke chart

Re: Chevy V8 bore & stroke chart